6. Verification
This section provides the tests that can be performed to verify proper configuration of Avaya Communication Manager, Avaya Application Enablement Services and MiaRec call recording application.

6.1. Verify Avaya Communication Manager

On Avaya Communication Manager, verify the status of the administered CTI links by using the "status aesvcs cti-link" command. The link status should show "no" for maintenance busy (Mnt Busy) and the Service State should indicate "established".
1
status aesvcs cti-link
2
3
AE SERVICES CTI LINK STATUS
4
5
CTI Version Mnt AE Services Service Msgs Msgs
6
Link Busy Server State Sent Rcvd
7
8
1 4 no aes-server1 established 15 15
Copied!
The "status aesvcs interface" command should indicate the interface is listening.
1
status aesvcs interface
2
3
AE SERVICES INTERFACE STATUS
4
5
Local Node Enabled? Number of Status
6
Connections
7
8
procr yes 1 listening
Copied!
The "status aesvcs link" command will indicate the number of messages sent from, and received at the CLAN interface (or procr), to and from Avaya Application Enablement Services, including maintenance traffic.
1
status aesvcs link
2
3
AE SERVICES LINK STATUS
4
5
Srvr/ AE Services Remote IP Remote Local Node Msgs Msgs
6
Link Server Port Sent Rcvd
7
8
01/01 aes-server1 10.0.0.25 43909 procr 224 209
Copied!
Once the MiaRec call recording application is running, the "list monitored-station" command will show each station, which is monitored by MiaRec via TSAPI interface.
1
list monitored-station
2
3
MONITORED STATION
4
5
Station Association 1 Association 2 Association 3 Association 4
6
Ext CTI Link CRV CTI Link CRV CTI Link CRV CTI Link CRV
7
------- ------------- ------------- ------------- -------------
8
32129 1 10
9
32130 1 9
10
32131 1 22
11
32132 1 7
Copied!

6.2. Verify Avaya Application Enablement Services

On Application Enablement Services, verify the status of the switch connection by selecting Status -> Status and Control -> Switch Conn Summary from the left pane. Verify that the Conn State is “Talking” for the switch connection associated with Avaya Communication Manager, and that the Associations column reflects the total number of monitored skill groups and agent stations as configured previously.
Verify the status of the TSAPI link by selecting Status -> Status and Control -> TSAPI Service Summary from the left pane. Verify the Conn Status is “Talking” as shown below.
Verify the status of the CTI User by selecting Status -> Status and Control -> TSAPI Service Summary from the left pane. Click the User Status button (not shown below). The CTI User Status screen is displayed. Verify that an open session exists for the CTI user created for MiaRec as shown below. This verification step assumes that MiaRec application is configured properly and running.

6.3. Verify TSAPI device monitoring status in MiaRec

Navigate in the MiaRec web interface to Administration -> System -> Recording Interfaces and click the Status link for the Avaya TSAPI interface.
In the Avaya TSAPI status screen, click the View TSAPI monitored devices link for the appropriate recorder instance (the screenshot below shows one instance).
In the Avaya TSAPI monitored devices screen, verify the status of the monitored devices. If any of devices shows a failed state, then click the extension link in that window to see the detailed error message.
The error message describes the actual reasons of failure. Read the message and apply appropriate corrections. For example, the message in the following screenshot says that device identifier (extension) is not valid. In this case, remove this extension from the Monitored Phones list in configuration.
If the Avaya TSAPI monitored devices screen shows none of devices (neither successfully monitored nor failed), then probably the TSAPI link connection is not established to AES server. In this case, navigate to Administration -> Maintenance -> System Log and check any error messages. The screenshot below shows that the TSAPI login/password is invalid. Make the appropriate corrections to the configuration.

6.4. Check MiaRec trace log

MiaRec provides detailed logging for troubleshooting purposes. Navigate to Administration -> Maintenance -> Troubleshooting to enable log in MiaRec.